产品搜索

首页 > 产品中心 > 空压机气源系列空压机气源系列

吸附式干燥机

吸附式干燥机

产品特点 Product features

※具有稳定一致的出气压力和露点

1.吸附塔之高度与直径经实验结果精密计算,塔床阻力小,保证了压缩气体干燥剂5秒的接触时间,满足成品气的露点要求。

2.30%的干燥剂余量,用于补偿干燥剂的自然老化,确保干燥。

3.大型扩散器,确保气流均匀通过干燥剂层,消除沟流现象。

※再生气量损耗小于14

1.卓越的机筒设计,保存100%的吸附热量,储存的热量用于增加再生阶段的再生气温度,提高设备的解吸能力,使得再生更彻底。

2.干燥和再生采用反向对流方案,湿空气流过干的吸附剂时效果较佳。再生气出口含湿量控制在亚饱和状态,使消声器及排气通道无结露之虑。

3.可根据干燥机的运行负载需求调节再生气用量,确保再生气流连续稳定,再生压力低至临界。

※干燥剂使用寿命长

1.合适的机筒尺寸,使气体通过干燥剂层的流速和时间保持好的状态,充分发挥干燥剂的性能。

2.合理的系统配置,在气流进入机筒前,经除油处理及时清除气流中内含油物与重污染物,避免干燥剂层受污染。

※设备采用了新颖高品质电动及气动阀和可靠的全电子可编程序控制器,人机界面友好,自动连续显示双塔工况,循环周期现场可编,出厂设定10min。阀门寿命长达50万次动作。

※筒体内壁作冷镀锌防锈处理,10年不锈蚀。

※动作准确、性能稳定、操作简便,安装无需基础。

 

Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

 

工况条件与技术指标 Working condition and technical indexes

额定进气温度Rated the inlet temperature

50

额定工作压力 Rated pressure

0.7 MPa0.4~1.0 MPa允许使用,6.4 MPa以下接受订货)

压力降Pressure drop

0.02MPa

压力露点Pressure dew point

-40(0.7MPa)(-60℃以下接受订货)

再生方式Regenerative way

无热再生

控制方式Control mode

全电子可编程序时间控制

工作周期Work cycle

T=410分钟(可调)

再生气量Regeneration gas

13%~15%

吸附剂Adsorbent

活性氧化铝

进气含油量Inlet oil content

0.1PPM

安装方式Installation

室内、无基础,混凝土地面找平,环境温度>0

 

主要技术参数 Main technical parameters

型号 Type(KXD-)

0005

0015

0030

0060

0120

0200

0320

0400

0500

0600

0800

1000

1200

处理量 Capacity m3/min

0.6

1.5

3.6

6.5

13.5

24

32

44

55

65

87

110

130

吸附剂填充量 Adsorbent filling quantity(KG)

16

38

89

160

340

590

790

1080

1360

1600

2150

2700

3200

外形尺寸

Appearance

and size

L(mm)

600

800

1000

1400

1600

2000

2100

2300

2480

2550

2600

2800

2830

W(mm)

310

410

500

530

640

650

710

780

1000

1000

1325

1564

1564

H(mm)

1050

1500

1600

1600

2260

2760

2800

2900

2950

2950

3180

3416

3672

接口尺寸 Interface size

ZG 1/2"

ZG 1"

ZG 1"

ZG 1.5"

ZG 2"

DN65

DN80

DN80

DN80

DN80

DN100

DN100

DN150

净重 Weight(kg)

100

140

240

400

780

1000

1425

1910

2300

2500

3400

4400

5200